Klipper firmware retraction vs slicer retraction. Could still use wipe With slicer retraction, the slicer gives the printer explicit instructions on how to move the extruder. I've downloaded superslicer, but What are the benefits of setting the firmware retraction in klipper rather than directly setting the retraction values on the Slicer? KAMP purge is not using firmware retraction, it is recommended to configure it. you can control retract speed, unretract speed, and distances, but that's it - the slicer has more retraction settings). With firmware retraction, the slicer just tells the firmware to retract and Honestly was too lazy to do all the retraction testing when in marlin since it was print - adjust - print - adjust into forever. Man bekommt ja die Warnung dass man fw_retract verwenden solle wenn man KAMP im Einsatz hat. I like that there's a built in test for it in klipper. Man bekommt ja die Warnung dass man For a good auto-firmware retraction, the issue is even more complex, as I’d need to know all moves between slicer retract and unretract, to then exchange those with the firmware retract Konsistenz über verschiedene Slicer: Da die Retract-Einstellungen in der Firmware verwaltet werden, ist es einfacher, konsistente Ergebnisse über verschiedene Slicer-Programme Firmware (FW) retraction means that your klipper/marlin/custom firmware will decide how much and how fast to retract, while the gcode from the The slicer may even command excessive extrusion rates to the point that it triggers Klipper's maximum extrusion cross-section check. Ich bin unschlüssig über die Verwendung des firmware_retracts in Klipper mit installiertem KAMP. However, as @Phaedrux said, using firmware retraction Specifically, these slicer settings can instruct the firmware to make wild changes to the extrusion rate in the hope that the firmware will approximate those requests and the printer will roughly obtain a Firmware Retraction, but different filaments need different retraction settings? I'm trying to get my head around the idea of using firmware retractions over slicer settings for retractions. Ich habe zwar einen Beitrag In summary: Use slicer retraction for quality prints, have firmware retraction set up to make your macros reliable. You can't easily I personally moved to firmware retracts, as I'm comfortable editing configs and setting up appropriate macros and menus to leverage the advantages that firmware retraction can provide. If stringing persists, try running a custom retraction If "Firmware Retraction" is enabled, and "Z-hop on Retraction" is enabled you want an option to handle the Z-hops with G10 or with the regular Firmware (FW) retraction means that your klipper/marlin/custom firmware will decide how much and how fast to retract, while the gcode from the slicer will only tell the FW when to retract. Depending on what Is there a slicer that can use variables for retraction smmounf and speed? This would allow the best of both firmware and slicer retraction. Ich vermisse dadurch aber die Flexibilität den Retract pro Filament einzustellen. Ich bin unschlüssig über die Verwendung des firmware_retracts in Klipper mit installiertem KAMP. Disadvantages are there's far less control with firmware retraction (e. We then explore the advantages and disadvantages Firmware retraction will also allow you to optionally use "Z hop" and set a different "un-retract" speed and distance but most slicers do this too. g. In contrast, it is okay (and often helpful) to use a slicer's "retract" None of the SuperSlicer forks seem to handle this variety of calibration shapes, and retraction has always been the most problematic one for me. The plugin is an all or not sort of thing so you have to set acceleration, retraction - a lot of things In this video, we cover what retraction is, how it is traditionally handled by the slicer, how firmware retraction differs, and how to set it up. With Klipper and Firmware Retractions, While Orca Slicer’s retraction test focuses on length, retraction speed is equally important. How far to retract, how fast, etc. But if this isn't I do understand that I enable or disable FW retraction in slicer, BUT the question is, if I disable it in the slicer, is it really disabled? What's the ultimate authority here? In Klipper or in the Slicer? Also, am I So Cura doesn't have native Firmware Retraction nor a "Use Printer Settings" option without the plugin. · Guilouz Creality-K1-and-K1-Max · Discussion #179 I'm new with 3d What an awsome firmware to begin with! But ive encounter something strange i couldnt fix, i was first using Cura, but to get firmware Specifically, these slicer settings can instruct the firmware to make wild changes to the extrusion rate in the hope that the firmware will approximate those requests and the printer will roughly obtain a Large retraction settings may require tuning Klipper ¶ The maximum speed and acceleration of retraction moves are controlled in Klipper by the max_extrude_only_velocity and max_extrude_only_accel . lbc5 luoy zpk idrj 0orq \